ENAMO GRIP is a two-component polyurethane finish considered within industrial protective coating systems. Selecting it requires more than choosing a colour. The finish must suit the substrate, the layers beneath it, the service environment and the application procedure. A clear specification explains the role of the topcoat and the conditions under which the complete system will be installed and used.

This guide focuses on the practical questions that arise when specifying ENAMO GRIP through GOLDTEC. It covers existing coatings, two-component handling, recoating, inspection and handover. The current manufacturer's documentation remains the reference for product-specific mixing, application and service requirements; this guide helps identify the project information needed to use that documentation effectively.

Define the function of the finish

State why a topcoat is required. The project may need a particular appearance, environmental resistance, a maintainable finish or another defined surface property. Record indoor or outdoor exposure, cleaning, contact with process materials and mechanical demands. General descriptions such as industrial durability should be translated into conditions that can be checked against the proposed material.

For chemical exposure, identify substances, concentrations, temperatures and contact duration. Occasional splash and continuous immersion are different requirements. For mechanically exposed areas, describe traffic, handling and likely damage. These details help distinguish a suitable finish from a coating selected on the basis of an attractive completed project photograph that may represent a very different service environment.

Check the substrate and the base system

On metal, establish substrate condition, contamination and corrosion protection requirements. On concrete, review surface condition, moisture and the proposed base layers. ENAMO GRIP is a finish, and the condition of the underlying system remains critical. A topcoat cannot correct a weak substrate or restore adhesion to an old layer that is separating from the surface.

Identify existing products where records are available. If the system is unknown, agree the investigation and preparation required before recoating. Confirm compatibility with the proposed base layers, including any anticorrosion coating. Where RUST GRIP is being considered as part of the same project, define the complete sequence and the conditions for applying the finish rather than assuming any interval or preparation is acceptable.

Illustration of the coating system or application
Image from the website application library, illustrating the type of substrate or application. It does not document a project described in this guide.

Treat concrete-floor applications as complete floor systems

A polyurethane finish may form part of a floor system, but the floor requirement extends beyond the finish. Assess concrete strength and surface condition, moisture, cracks, joints, traffic and cleaning. Define whether repairs, levelling or additional layers are needed. A product offered for a suitable substrate is not automatically a complete system for a heavily trafficked or chemically exposed production floor.

If slip resistance is required, specify it for the actual system and use conditions. Texture and cleaning needs should be considered together. Requirements related to hygiene, food contact or other controlled environments also need application-specific verification. Send these requirements at the start of the enquiry so the proposed system is reviewed against them before material selection and installation planning proceed.

Plan two-component handling before application

The application team must follow the current instructions for component identification, mixing and usable time. Do not infer proportions from the size of the containers or change the ratio to alter handling. Use suitable equipment and a procedure that operators can repeat. Where partial batches are proposed, confirm that the method is permitted and controlled for the supplied product.

Plan work areas and batch sizes together. Material that has exceeded its permitted working time should not be made usable by an improvised addition. Environmental and substrate conditions may influence the process, so the team needs the relevant limits and monitoring method. These details belong in the work plan before coating starts, particularly when the site has restricted access or short shutdown windows.

Define preparation between layers and recoating windows

Recoating depends on the installed layer, elapsed time and current product instructions. State the required conditions in the application procedure. If work is delayed, review whether additional preparation is needed rather than resuming from the original programme without checking. This is especially relevant on outdoor work where weather or access interruptions can change the planned sequence.

Record layer completion times and any preparation carried out before the next application. Ensure the same information is available across shifts and contractors. A finish applied over a suitable base at the wrong stage may create a problem that is not visible during immediate visual inspection. Consistent records make it easier to confirm compliance and investigate any later issue without relying on memory.

Preparation and application considerations
Image from the website application library, illustrating the type of substrate or application. It does not document a project described in this guide.

Agree inspection and return-to-service requirements

The inspection plan should identify the relevant checks for the complete system. These can include substrate acceptance, application conditions, layer thickness and final appearance where specified. Establish how defects are located, repaired and reinspected. Use methods appropriate to the coating and substrate rather than applying a generic checklist that may omit the project's critical requirement.

Distinguish dry-to-touch conditions from readiness for further coating, mechanical loading and chemical exposure. The production team needs a clear release condition before cleaning the area, moving equipment or restarting the process. Schedule the required cure and acceptance steps explicitly. A surface that looks finished may still require time under suitable conditions before it is ready for the intended service.

Keep finish expectations and maintenance practical

Where appearance is important, agree a representative sample or trial area before broad installation. Define the relevant colour and finish expectations, while recognizing that geometry and application conditions can affect the visual result. The sample should include the intended substrate preparation and layers, not merely a small patch of topcoat on a different surface.

At handover, keep the system specification, product details, application record and repair guidance. Identify cleaning materials and methods that suit the installed system. Local mechanical damage should be assessed using the actual layer sequence so that a repair restores the intended system rather than introducing an unidentified patch material. Record later changes in service exposure and review compatibility when needed.

Discuss the project with GOLDTEC

Send the substrate, area, existing layers, service exposure and desired result when requesting an ENAMO GRIP recommendation. Include photographs and any mandatory specification. For floors add traffic, moisture and cleaning information; for metal add corrosion condition and the proposed base protection. Access and shutdown constraints help establish whether the planned procedure can be carried out reliably.

Use the enquiry form to contact GOLDTEC about ENAMO GRIP and compatible protection products. A focused discussion can establish the topcoat's role, the information still needed and the scope of a useful quotation. The resulting decision should connect material selection with preparation, application and service requirements, giving both procurement and the installation team a clear basis for the work.

Frequently asked questions

What type of coating is ENAMO GRIP?

ENAMO GRIP is a two-component polyurethane finish from SPI. Review the current technical documentation for the proposed application and complete layer system. It should not be treated as an epoxy product or a universal specification for every concrete floor.

Can ENAMO GRIP be applied over an existing coating?

Only after the existing system is assessed and compatibility, adhesion and preparation requirements are established. A stable-looking finish may conceal weak underlying layers. Review the proposed combination and consider a representative trial where appropriate.

How is the mixing ratio determined?

Use the current manufacturer's instructions for the exact product supplied. Do not estimate the ratio from container appearance, divide components informally or add thinner without an approved instruction. Plan batch sizes around the specified usable time and actual conditions.

When can the coated surface return to service?

The answer depends on the selected system, application conditions and type of exposure. Dry to touch, ready to recoat and ready for chemical or mechanical service are different stages. Use the product instructions and project acceptance requirements.

What should I provide for an ENAMO GRIP enquiry?

Provide substrate type, existing layers, area, exposure, desired finish and access conditions. For floors include traffic, cleaning chemicals, moisture information and slip-resistance requirements. State any mandatory specification so suitability can be checked before quotation.

Sources and technical references

Manufacturer data applies to a specific grade and system. Define the project specification against the substrate, exposure and current manufacturer instructions.

Share this guideLinkedIn ↗WhatsApp ↗