RUST GRIP is a single-component urethane coating considered for corrosion encapsulation and protection of suitable substrates. Its project role needs to be defined alongside surface preparation, actual exposure and the condition of the metal. Encapsulation is a coating approach, rather than a reason to ignore loose material, contamination or damage that requires engineering repair.

This guide focuses on planning a RUST GRIP project with GOLDTEC. It explains the questions to resolve before specifying the material, the decisions that belong in the application scope and the records needed for maintenance. Use current manufacturer documentation for the exact application requirements and connect that information with the condition of the actual asset.

Understand what encapsulation does and does not establish

An encapsulation coating forms part of a protective system over a suitably prepared surface. It is different from removing rust or chemically converting it. These terms describe different functions and should not be used interchangeably in a quotation. Ask the proposal to explain the intended role of the coating and the condition of the substrate on which that role depends.

The coating does not restore lost steel thickness or certify the integrity of a structure. Significant pitting, perforation or deterioration at connections requires assessment by the responsible qualified personnel. Identify these issues before defining the coating area. The protection project can then proceed over a substrate released for that purpose, with structural repairs and surface treatment kept clear in the scope.

Survey corrosion and existing coating together

Map affected areas with photographs and location references. Record loose material, flaking layers, rust at edges and water traps. Inspect accessible joints, welds and supports rather than relying on the broad visible surface alone. If records identify previous coatings, include them in the review. Unknown layers should be treated as an uncertainty requiring investigation, not assumed to be compatible.

Group areas with similar condition while noting exceptions. A heavily exposed base may need different preparation from an upper member protected from frequent wetting. Differences in condition influence work effort and inspection. A survey that shows these areas separately helps GOLDTEC review the proposed product role and allows an applicator to quote a realistic preparation scope.

Illustration of the coating system or application
Image from the website application library, illustrating the type of substrate or application. It does not document a project described in this guide.

Define the service exposure for the proposed system

Describe moisture, salt, process contamination, washing, temperature and likely mechanical damage. Include both normal operation and foreseeable events such as periodic cleaning. Exposure details determine what needs to be checked against the product information. A structure close to the sea and equipment inside a process building may both face corrosion but require different assessment of their service conditions.

If the project includes immersion, hot equipment or another specific condition, state it explicitly. Do not extrapolate a general anticorrosion description to a demanding exposure without verification. Where another protective or thermal layer will be part of the system, identify it during the initial enquiry so compatibility and the application sequence can be reviewed before products are ordered independently.

Agree preparation and its acceptance point

Preparation must achieve the surface condition required by the selected system. Address contamination, loose material and unstable existing coatings using the approved method. The project should state who performs preparation, who checks it and what happens when additional deterioration is exposed. This avoids hiding unresolved conditions beneath the first coating layer.

Site constraints can affect the feasible preparation method. Record access, nearby equipment, operating restrictions and waste-control requirements. If the initially proposed method cannot be used, review the technical implications before changing the procedure. Choosing a coating does not eliminate the need to deliver a suitable substrate, and applying more material cannot be assumed to compensate for inadequate preparation.

Specify RUST GRIP and any associated finish

Use the RUST GRIP product information as the starting point for a grade-specific technical review. The specification should identify the product, preparation, application requirements and relevant inspection. Confirm that the current instructions are available to the applicator and that the work programme allows the required conditions and sequence.

Where a polyurethane finish is proposed, ENAMO GRIP can be examined within a compatible system. Its role differs from the underlying corrosion-protection layer. Confirm the recoating requirements rather than assuming that any interval is acceptable. The complete system should remain identifiable in the quotation and handover, so future repairs can reproduce the intended sequence.

Preparation and application considerations
Image from the website application library, illustrating the type of substrate or application. It does not document a project described in this guide.

Give difficult details their own work instructions

Edges, welds, fasteners and narrow gaps may require specific attention during preparation and application. Identify them in the scope and decide how they will be inspected. A uniform appearance on flat steel does not demonstrate continuity around a complicated connection. Where water remains trapped, consider whether a detail improvement is needed alongside the protective coating.

Define inaccessible areas and the boundary of the work. Treating only the accessible face of a member is different from a full-perimeter system. If temporary access or disassembly is needed, plan it before installation. Clear boundaries help the owner understand which areas received the specified protection and prevent later maintenance teams from assuming that an uncoated concealed surface was part of the completed project.

Record application quality and repairs

Set the inspection plan before work begins. Record material identification, substrate acceptance, relevant conditions and the checks required by the system. Define how thickness and other properties will be verified where specified. If a defect is found, locate it in the record and document the corrective work and reinspection before final acceptance.

Manufacturer test evidence should be used within its stated scope. Do not convert laboratory salt-exposure hours directly into service years or assume a result for one system predicts every field installation. The useful project evidence combines the selected product information with records showing that the actual work followed the approved specification under the documented conditions.

Plan maintenance and request a focused review

At handover, retain photographs, treated-area references, system details, inspection records and repair guidance. Establish priorities for checking vulnerable details and mechanically exposed areas. When local damage occurs, assess its extent and substrate condition before repair. Keeping a small issue identifiable and documented is more useful than repeatedly covering it with an unknown matching paint.

Contact GOLDTEC with the asset type, area, photographs, corrosion condition, existing layers and service exposure. Include access and shutdown constraints and any mandatory specification. Use the enquiry form to discuss RUST GRIP and associated finish requirements. These details support a recommendation and quotation that explain what the material will do, how the substrate will be prepared and what evidence will support acceptance.

Frequently asked questions

Is RUST GRIP a rust converter or remover?

RUST GRIP is a single-component urethane coating used for corrosion encapsulation and protection. It is not a chemical rust converter or a rust-removal process. The surface must still be prepared according to the current product and project requirements.

Can I coat loose rust without preparation?

Do not interpret encapsulation as permission to coat any surface as found. Loose material, contamination and unsuitable existing layers require treatment. The selected preparation must match the product instructions and the actual substrate condition.

Can RUST GRIP repair holes or lost steel thickness?

A protective coating does not restore structural metal. Perforation, significant loss of section or damaged connections require assessment and repair by the responsible qualified personnel before a coating system is considered.

When is a finish such as ENAMO GRIP considered?

A finish may be proposed when the service and appearance requirements justify it and the complete layer system is compatible. Confirm preparation, sequence and recoating conditions using current technical guidance for the exact products.

How should local damage be repaired?

Identify the installed system and extent of damage, assess the substrate and follow an approved repair procedure. Keep repair locations and materials in the maintenance record. Do not patch with an unidentified material solely because its colour matches.

Sources and technical references

Manufacturer data applies to a specific grade and system. Define the project specification against the substrate, exposure and current manufacturer instructions.

Share this guideLinkedIn ↗WhatsApp ↗